do not scale from this print isdf-xx-d-x no of positions -02 thru -50 (per row) row specification -d: double row notch specification leave blank: no notch -c: chamfer (see sheet 2, fig 2) (7 position only) -l: friction lock (see sheet 2, fig 3) (available on pos 10 - 30) -r: retention latch (available on pos -05 thru -30) (see sheet 3, fig 4) (see note 11) ((no of pos x .050) + .015) .025 (typ) .180 .250 .020 (typ) r .001 .1450 .1200 (tol non-accum) (no of pos x .050) - .050 "a" "a" c l c l .002 .005 see note 3 a c1 fig. 1 isdf-10-d-x shown see note 2 .0800 .0020 .050 .0260 .0420 r .001 "b" "b" 'c' section "a"-"a" c l c2 c3 .003 'd' "f" "f" 02 01 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 see note 8 .440 .4260 .415 .058 .077 .103 .0150 ref .0430 .0525 r .005 typ .0500 'e' section "b"-"b" c5 c4 c6 .003 .050 .030 .030 .033 see note 4 .2180 .0410 section "f"-"f" c7 c8 .070 c l see note 7 c k sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .003 [.08] .xxxx: .0015 [.038] material: .050" cl crimp wire socket insulator by: isdf-xx-d-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 5/4/2005 3 1 sheet scale: 4:1 vectra s475, color: black f:\dwg\misc\mktg\isdf-xx-d-x-mkt.slddrw notes: 1. represents a critical dimension. 2. samtec logos shall appear at locations on surface shown, approximately .075 x .055 (both sides). 3. all multiple cavity molds shall identify each cavity with a letter designation located where shown. 4. identification marks not to protrude beyond .001 above the surface of the insulator material. 5. molded surfaces shall be consistent and smooth. surfaces to be free of scatches, nicks, sink areas, voids or other blemishes. 6. part to be symmetric about the centerline within +/-.0015, unless otherwise stated. 7. gate pads must be recessed .005. 8. specified positions to be identified where shown (note 4 applies). 9. r.005 optional. 10. positions -10 through -24 will have only one latch lock at dimension shown; positions -25 through -30 will have two latch locks at dimension shown. 11. option not for sale. for retention latch feature, see isdf-xx-d-m print. max regrind: 50% max flash allowed: .002 max gate vestige: .004 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision k
.040 sq .0120 .0220 sq 90 .0350 - .0010 + .0015 sq detail 'c' scale 16 : 1 c9 detail 'd' scale 16 : 1 30 r .0025 (typ) .0075 detail 'e' scale 16 : 1 30 .035 fig. 2 isdf-07-d-c shown same as fig. 1 unless specified 01 03 05 07 09 11 13 02 04 06 08 10 12 14 .3050 (typ) (see note 10) .1000 (typ) "g" "g" fig. 3 isdf-25-d-l shown same as fig. 1 except as shown .0350 (typ) r .025 (typ) r .010 (typ) .027 - .000 + .003 (typ) section "g"-"g" scale 4 : 1 sheet of .050" cl crimp wire socket insulator by: isdf-xx-d-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 5/4/2005 3 2 sheet scale: 1:0.166667 f:\dwg\misc\mktg\isdf-xx-d-x-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision k
.440 ref ((no of pos x .050) + .015) - .002 + .000 .020 "h" "h" 'j' fig. 4 -r: retention latch option (see note 11) (isdf-05-d-r shown) (same as fig. 1 except as shown) c11 .1740 .0300 .065 .1480 .360 .002 8 section "h"-"h" c l c9 ((no of pos x .050) + .145) - .005 + .002 ((no of pos x .0500) + .0700) .002 'k' c l c10 .015 45 x (typ) .0140 .0010 r .004 (4 plcs) r .0020 (typ) .0095 - .0005 + .0010 detail 'k' scale 10 : 1 30 (typ) .005 .002 (typ) .0270 45 .0023 .0190 15 detail 'j' scale 12 : 1 sheet of .050" cl crimp wire socket insulator by: isdf-xx-d-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 5/4/2005 3 3 sheet scale: 6:1 f:\dwg\misc\mktg\isdf-xx-d-x-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision k
|
